{"id":1511,"date":"2023-10-30T10:15:12","date_gmt":"2023-10-30T02:15:12","guid":{"rendered":"https:\/\/www.jotuns.com\/?p=1511"},"modified":"2024-06-07T08:28:25","modified_gmt":"2024-06-07T00:28:25","slug":"product-description","status":"publish","type":"post","link":"https:\/\/www.jotuns.com\/jotunchanpin\/1511.html","title":{"rendered":"Product\u00a0 description"},"content":{"rendered":"\n
Tankguard Plus<\/td><\/tr>
Product\u00a0 description<\/td><\/tr>
This  is  a  two  component  polyamine  cured  phenolic\/novolac  epoxy  coating.  It  has  a  high  resistance  to  most  sour
crude  oils  and  a  wide  range  of  chemicals  and  solvents.  It  has  outstanding  chemical  resistance  to  crude  oll  at
temperatures  up  to  160  C.  Can  be  used  as  primer,  mid  coat  or  finish  coat  in  atmospheric  and  immersed
environments.  Sultable  for   properly   prepared  carbon  steel,  galvanised  steel,  stainless  steel  and  concrete
substrates.<\/td><\/tr>
Typical    use
Protective:<\/td><\/tr>
Speclally  deslgned  as  an  intemal  lining  for  offshore,  onshore  and  burled  tanks  and  plpes  such  as  chemlcal
storage,  waste  water,  grey  water,  process  water,  concrete  bund,  fire  service  lines  and  drilling  mud  tanks.  This
coating  has  very  good  resistance  to  high  temperature  products.  Refer  to  Protective  Product  Resistance  List.<\/td><\/tr>
Approvals            and             certificates<\/td><\/tr>
In  compliance  with  Federal  Drug  Authority,  USA,  FDA  Title  21,  Part  175.300,  approved  for  exposure  to  dry  and
liquld   foods<\/td><\/tr>
Additional  certificates  and  approvals   may  be  avallable  on  request.

Colours<\/td><\/tr>
buff,    white<\/td><\/tr>
Product                data<\/td><\/tr>
Property<\/td>   Test\/Standard<\/td>    Description<\/td><\/td><\/tr>
Solids by volume<\/td>   IS03233<\/td>   70\u00b12%<\/td><\/tr>
Gloss level (GU 60\u00b0)<\/td>   ISO 2813<\/td> seml gloss(35-70)<\/td><\/tr>
lash point<\/td>   IS03679 Method 1<\/td>  28 \u2103<\/td><\/tr>
Density<\/td>   calculated<\/td> 1.6 kg\/<\/td><\/tr>
VOC-US\/Hong Kong<\/td>   US EPA method 24(tested)<\/td>  300 g\/l<\/td><\/tr>
<\/td>   (CARB(SCM)2007,SCAQMD rule 1113,Hong Kong)<\/td><\/tr>
VQC-EU<\/td>   IED(2010\/75\/EU)(theoretical<\/td> 342 g\/<\/td><\/tr>
VOC-China<\/td>   GB\/T 23985-2009 (tested)<\/td> 237 g\/<\/td><\/tr>
VOC-Korea<\/td>   Korea Clean Air Conservation Act (tested)<\/td> 259 g\/l<\/td><\/tr>
<\/td>   Max. thinning ratio Included)<\/td><\/td><\/tr>
The  provided  data  is  typical  for  factory  produced  products,  subject  to  slight  variation  depending  on  colour.
All  data  is  valid  for  mixed  paint.<\/td><\/tr>
Gloss   description:   According   to   Jotun   Performance   Coatings'   definition.<\/td><\/tr>
Date of issue:    25 May 2022<\/td>Page:1\/5<\/td><\/tr>
This Technical Data Sheet supersedes those previously issued,<\/td><\/tr>
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Gulde (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com<\/td><\/tr>
Technical<\/td>Data<\/td><\/td>Sheet<\/td><\/td><\/tr>
Tankguard<\/td>Plus<\/td><\/td>Jotun Protects Preperty<\/td><\/tr>
Film          thickness          per          coat<\/td><\/tr>
Typical recommended specification range<\/td><\/tr>
Dry   film   thickness                             100  -  150   \u03bcm<\/td><\/tr>
Wet   film   thickness                            140  -  215   um<\/td><\/tr>
Theoretical   spreading   rate                 7   -  4.7  m\u00b2\/l<\/td><\/tr>
Surface                      preparation<\/td><\/tr>
To  secure  lasting  adhesion  to  the  subsequent  product  all  surfaces  shall  be  dean,  dry  and  free  from  any
contamination.<\/td><\/tr>
Surface            preparation            summary            table<\/td><\/tr>
Substrate<\/td>Surface  p
Minimum<\/td>		reparation
           Recommended<\/td>		<\/td><\/tr>
Carbon steel<\/td>Sa   22(ISO   8501-1)<\/td>Sa   22(ISO   8501-1)<\/td><\/tr>
Stalnless stee<\/td>The surface shall be hand or machine
abraded with non-metallic abrasives
or bonded filbre machine or hand
abrasive pads to impart a scratch
pattern to the surface<\/td>		Abraslve blast cleaning to achleve a
surface profille using non-metallic
abrasive media which is suitable to
achieve a sharp and angular surface
profile.<\/td><\/tr>
Galvanised steel<\/td>The surface shall be clean, dry and
appear with a rough and dull proflle<\/td>		Sweep blast-cleaning using non-
metallic abraslve leaving a clean,
ough  and  even  pattern<\/td><\/tr>
Concrete<\/td>Dry abrasive blast cleaning to SSPC-
SP  13\/NACE  No.  6<\/td>		Dry abrasive blast cleaning to SSPC-
SP  13\/NACE No. 6.<\/td><\/tr>
Application<\/td><\/tr>
Application<\/td>methods<\/td><\/td><\/tr>
The  product<\/td>can  be  applled  by<\/td><\/tr>
Spray:<\/td>Use  airless  spray<\/td><\/td><\/tr>
Brush:<\/td>Recommended  for  stripe  coating  and  small  areas,  care  must  be  taken  to  achieve  the
specified   dry   film   thickness.<\/td><\/tr>
Roller:<\/td>Roller  application  only  to  be  used  for  scallops,  ratholes,  small  plpes  etc.<\/td><\/tr>
Date of issue:    25 May 2022<\/td>Page: 2\/5<\/td><\/tr>
This Technical Data Sheet supersedes those previously issued,<\/td><\/tr>
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Gulde (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com<\/td><\/tr>
Technical<\/td>Data<\/td><\/td>Sheet<\/td><\/td><\/tr>
Tankguard<\/td>Plus<\/td><\/td>Jotun Protects Preperty<\/td><\/tr>
Product<\/td>mixing      ratio(by<\/td>volume)<\/td><\/tr>
Tankguard<\/td>Plus  Comp A<\/td><\/td>4<\/td>part(s)<\/td><\/tr>
Tankguard<\/td>Plus  Comp.  B<\/td>1<\/td>part(s)<\/td><\/tr>
Thinner\/Cleaning                      solvent<\/td><\/tr>
Thinner:                                       Jotun  Thinner  No.  23<\/td><\/tr>
Gulding       data       for       alrless       spray
Nozzle       tip(inch\/1000):                                17-21
Pressure   at   nozzle   (minimum):                  150  bar\/2100  psl<\/td><\/tr>
Drying and Curing time<\/td><\/tr>
Substrate temperature<\/td> 5\u00b0C<\/td>10 \u2103<\/td>15 C<\/td>23 C<\/td>30 C<\/td>  40C<\/td><\/td><\/tr>
Surface(touch) dry<\/td> 24 h<\/td>16 h<\/td>6 h<\/td>4 h<\/td>3 h<\/td>2 h<\/td><\/tr>
Walk-on-dry<\/td> 36 h<\/td>24 h<\/td>10 h<\/td>7 h<\/td>5 h<\/td>3 h<\/td><\/tr>
Dry to over coat, minimum<\/td>  52 h<\/td> 36 h<\/td>30 h<\/td> 20 h<\/td>14 h<\/td> 10 h<\/td><\/tr>
For  maximum  overcoating  intervals,  refer  to  the  Application  Guide  (AG)  for  this  product.<\/td><\/tr>
If  a  hot  cure  Is  performed  Tankguard  Plus  can  be  returned  to  servlce  in  half  the  \"Drled\/cured  for  servlce\"  time,
as  stated   below:<\/td><\/tr>
5\u00b0C:7  d   Included  8   h  @60\u00b0\u2103
10 \u00b0 \u2103: 5d  included 8  h @60 \u00b0 \u2103
15\u00b0\u2103:  3.5  d  induded  8  h  @60\u2103
23  \u00b0 \u2103: 2.5  d  included  8  h @60\u00b0\u2103
30\u00b0\u2103:  2  d  included  8  h  @60\u2103
40  \u00b0C:  1.5  d  induded  8h  @60  \u2103<\/td><\/tr>
Hot  cure(by  air)  can  be  initiated  after  the  last  coat  has  become  \"Dry  to  overcoat\",  and  can  be  achieved  by
heating  with  hot  air  until  a  steel  temperature  of  60  \u00b0C  is  held  for  8  hours.  Total  curing  time  must  be  as  outlined
above.<\/td><\/tr>
Drying  and  curing  times  are  determined  under  controlled  temperatures  and  relative  humidity  below  85  %,  and
at  average  of  the  DFT  range  for  the  product.<\/td><\/tr>
Surface  (touch)  dry:  The  state  of  drying  when  slight  pressure  with  a  finger  does  not  leave  an  imprint  or  reveal
tackiness.<\/td><\/tr>
Walk-on-dry:   Minimum   time   before   the   coating   can   tolerate   normal   foot   traffic   without   permanent   marks,
Imprints   or   other   physical   damage.<\/td><\/tr>
Dry  to  over  coat,  minimum:  The  recommended  shortest  time  before  the  next  coat  can  be  applied.

Drled\/cured  for  servlce:  Minimum  time  before  the  coating  can  be  permanently  exposed  to  the   Intended<\/td><\/tr>
environment\/medium.<\/td><\/tr>
Date of issue:    25 May 2022<\/td>Page:3\/5<\/td><\/tr>
This Technical Data Sheet supersedes those previously issued,<\/td><\/tr>
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Gulde (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com<\/td><\/tr>
Technical<\/td>Data<\/td><\/td>Sheet<\/td><\/td>JOTUN<\/td><\/tr>
Tankguard<\/td>Plus<\/td><\/td>Jotun Protects Preperty<\/td><\/tr>
Induction time and Pot life<\/td><\/tr>
Paint         temperature                                                                                                          23 \u2103

Induction    time                                                                                                                    15  min<\/td><\/tr>
Pot  life                                                                                                                                     2  h


Heat                 resistance<\/td><\/tr>
<\/td>               Temperature
    Continuous<\/td>		Peak<\/td><\/td><\/tr>
Dry, atmospheric<\/td> 160 C<\/td><\/tr>
[mmersed, sea water<\/td>90 C<\/td>95 \u2103<\/td><\/tr>
[mmersed, crude ai<\/td> 160 C<\/td><\/tr>
Further  reslstance  Information  can  be  found  in  Protective  Product  Resistance  List  avallable  on  Jotun's  website,  or
contact  your  local  Jotun  office.<\/td><\/tr>
Peak   temperature   duration   max.1   hour.<\/td><\/tr>
The  temperatures   listed   relate  to   retention  of  protective   properties.  Aesthetic   properties   may  suffer  at  these
temperatures.<\/td><\/tr>
Note  that  the  coating  will  be  resistant  to  various  immersion  temperatures  depending  on  the  specific  chemical
and  whether  immersion   Iis  constant  or  intermittent.  Heat  resistance  is   Infuenced  by  the  total  coating  system.   If
used  as  part  of  a  system,  ensure  all  coatings  In  the  system  have  similar  heat  resistance.<\/td><\/tr>
Product                           compatibility<\/td><\/tr>
Depending  on  the  actual  exposure  of  the  coating  system,  various  primers  and  topcoats  can  be  used  in
combination  with  this  product.  Some  examples  are  shown  below.  Contact  Jotun  for  specific  system
recommendation.<\/td><\/tr>
Prevlous   coat:                    itself  only
Subsequent    coat:              itself  only<\/td><\/tr>
Packaging (typical)<\/td><\/tr>
Volume<\/td>Size     of     containers<\/td><\/tr>
(litres)<\/td>(litres)<\/td><\/tr>
Tankguard  Plus  Comp  A<\/td>16<\/td><\/td>20<\/td><\/tr>
Tankguard  Plus  Comp.  B<\/td>4<\/td>5<\/td><\/tr>
The  volume  stated  is  for  factory  made  colours.  Note  that  local  variants  in  pack  size  and  filled  volumes  can  vary
due  to  local  regulations.<\/td><\/tr>
Storage<\/td><\/tr>
Date of issue:    25 May 2022<\/td>Page:4\/5<\/td><\/tr>
This Technical Data Sheet supersedes those previously issued,<\/td><\/tr>
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Gulde (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com<\/td><\/tr>
Technical<\/td>Data        Sheet<\/td><\/td><\/tr>
Tankguard<\/td><\/td>Plus<\/td><\/td><\/tr>
<\/td>Jotun Protects Preperty<\/td><\/tr>
The  product  must  be  stored  in  accordance  wlth  natlonal  regulations.  Keep  the  containers  in  a  dry,  cool,  well
ventllated  space  and  away  from  sources  of  heat  and  lgnltlon.  Containers  must  be  kept  tightly  closed.  Handle
with   care.<\/td><\/tr>
Shelf     life     at     23     \u2103<\/td><\/tr>
Tankguard  Plus  Comp  A                                                              24    month(s)
Tankguard  Plus  Comp.  B                                                             24    month(s)<\/td><\/tr>
In  some  markets  commerclal  shelf  life  can  be  dictated  shorter  by  local  legislation.  The  above  is  minimum  shelf
life,  thereafter  the   paint  quallty   is  subject  to   re-Inspection.<\/td><\/tr>
Caution<\/td><\/tr>
This  product  is  for  professional  use  only.  The  applicators  and  operators  shall  be  trained,  expenienced  and  have
the  capabilty  and  equipment  to  mix\/stir  and  apply  the  coatings  correctly  and  according  to  Jotun's  technical
documentation.   Applicators   and   operators   shall   use   appropriate   personal   protection   equipment   when   using   this
product.  This  guideline  is  given  based  on  the  current  knowledge  of  the  product.  Any  suggested  deviation  to  sulit
the  site  conditions  shall   be  forwarded  to  the   responsible  Jotun   representative  for  approval   before  commencing
the   work.<\/td><\/tr>
Health           and           safety<\/td><\/tr>
Please  observe  the  precautionary  notices  displayed  on  the  container.  Use  under  well  ventilated  conditions.  Do
not  inhale  spray  mist.  Avoid  skin  contact.  Spillage  on  the  skin  should  immediately  be  removed  with  suitable
cleanser,  soap  and  water.  Eyes  should  be  well  flushed  with  water  and  medical  attention  sought  immediately.<\/td><\/tr>
Colour                   variation<\/td><\/tr>
When  applicable,  products  primarily  meant  for  use  as  primers  or  antifoulings  may  have  slight  colour  variations
from  batch  to  batch.  Such  products  and  epoxy  based  products  used  as  a  finish  coat  may  chalk  when  exposed  to
sunlight   and   weathering.<\/td><\/tr>
Colour  and  gloss  retention  on  topcoats\/finish  coats  may  vary  depending  on  type  of  colour,  exposure
environment  such  as  temperature,   UV  intensity  etc.,  application  quality  and  generic  type  of  paint.  Contact  your
local   Jotun   office   for  further   information.<\/td><\/tr>
Disclaime         r<\/td><\/tr>
The  information  in  this  document  is  given  to  the  best  of  Jotun's  knowledge,  based  on  laboratory  testing  and
practical  experience.  Jotun's  products  are  considered  as  semi-finished  goods  and  as  such,  products  are  often
used  under  conditions  beyond  Jotun's  control.  Jotun  cannot  guarantee  anything  but  the  quality  of  the  product
itself.   Minor  product  variations  may  be  implemented  in  order  to  comply  with  local  requirements.  Jotun  reserves
the  right  to  change  the  given  data  without  further  notice.<\/td><\/tr>
Users  should  always  consult  Jotun  for  specific  guidance  on  the  general  suitability  of  this  product  for  their  needs
and   speclfic   appllcatlon   practices.<\/td><\/tr>
If  there  is  any  inconsistency  between  different  language  issues  of  this  document,  the  English  (United  Kingdom)
verslon   will   prevall.<\/td><\/tr><\/tbody><\/table><\/figure>\n","protected":false},"excerpt":{"rendered":"

Tankguard Plus Product\u00a0 description This  is& …<\/p>\n

Product\u00a0 description<\/span> \u67e5\u770b\u5168\u6587 »<\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","footnotes":""},"categories":[10],"tags":[70],"class_list":["post-1511","post","type-post","status-publish","format-standard","hentry","category-jotunchanpin","tag-70"],"_links":{"self":[{"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/posts\/1511","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/comments?post=1511"}],"version-history":[{"count":2,"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/posts\/1511\/revisions"}],"predecessor-version":[{"id":5897,"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/posts\/1511\/revisions\/5897"}],"wp:attachment":[{"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/media?parent=1511"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/categories?post=1511"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.jotuns.com\/wp-json\/wp\/v2\/tags?post=1511"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}