| Product? description | |||||||||||||||||||||||
| This is a two component polyamine cured phenolic/novolac epoxy coating. It has a high resistance to most sour crude oils and a wide range of chemicals and solvents. It has outstanding chemical resistance to crude oll at temperatures up to 160 C. Can be used as primer, mid coat or finish coat in atmospheric and immersed environments. Sultable for properly prepared carbon steel, galvanised steel, stainless steel and concrete substrates. | |||||||||||||||||||||||
| Typical use Protective: | |||||||||||||||||||||||
| Speclally deslgned as an intemal lining for offshore, onshore and burled tanks and plpes such as chemlcal storage, waste water, grey water, process water, concrete bund, fire service lines and drilling mud tanks. This coating has very good resistance to high temperature products. Refer to Protective Product Resistance List. | |||||||||||||||||||||||
| Approvals and certificates | |||||||||||||||||||||||
| In compliance with Federal Drug Authority, USA, FDA Title 21, Part 175.300, approved for exposure to dry and liquld foods | |||||||||||||||||||||||
| Additional certificates and approvals may be avallable on request. Colours | |||||||||||||||||||||||
| buff, white | |||||||||||||||||||||||
| Product data | |||||||||||||||||||||||
| Property | Test/Standard | Description | |||||||||||||||||||||
| Solids by volume | IS03233 | 70±2% | |||||||||||||||||||||
| Gloss level (GU 60°) | ISO 2813 | seml gloss(35-70) | |||||||||||||||||||||
| lash point | IS03679 Method 1 | 28 ℃ | |||||||||||||||||||||
| Density | calculated | 1.6 kg/ | |||||||||||||||||||||
| VOC-US/Hong Kong | US EPA method 24(tested) | 300 g/l | |||||||||||||||||||||
| (CARB(SCM)2007,SCAQMD rule 1113,Hong Kong) | |||||||||||||||||||||||
| VQC-EU | IED(2010/75/EU)(theoretical | 342 g/ | |||||||||||||||||||||
| VOC-China | GB/T 23985-2009 (tested) | 237 g/ | |||||||||||||||||||||
| VOC-Korea | Korea Clean Air Conservation Act (tested) | 259 g/l | |||||||||||||||||||||
| Max. thinning ratio Included) | |||||||||||||||||||||||
| The provided data is typical for factory produced products, subject to slight variation depending on colour. All data is valid for mixed paint. | |||||||||||||||||||||||
| Gloss description: According to Jotun Performance Coatings' definition. | |||||||||||||||||||||||
| Date of issue: 25 May 2022 | Page:1/5 | ||||||||||||||||||||||
| This Technical Data Sheet supersedes those previously issued, | |||||||||||||||||||||||
| The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Gulde (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com | |||||||||||||||||||||||
| Technical | Data | Sheet | |||||||||||||||||||||
| Tankguard | Plus | Jotun Protects Preperty | |||||||||||||||||||||
| Film thickness per coat | |||||||||||||||||||||||
| Typical recommended specification range | |||||||||||||||||||||||
| Dry film thickness 100 - 150 μm | |||||||||||||||||||||||
| Wet film thickness 140 - 215 um | |||||||||||||||||||||||
| Theoretical spreading rate 7 - 4.7 m2/l | |||||||||||||||||||||||
| Surface preparation | |||||||||||||||||||||||
| To secure lasting adhesion to the subsequent product all surfaces shall be dean, dry and free from any contamination. | |||||||||||||||||||||||
| Surface preparation summary table | |||||||||||||||||||||||
| Substrate | Surface p Minimum | reparation Recommended | |||||||||||||||||||||
| Carbon steel | Sa 22(ISO 8501-1) | Sa 22(ISO 8501-1) | |||||||||||||||||||||
| Stalnless stee | The surface shall be hand or machine abraded with non-metallic abrasives or bonded filbre machine or hand abrasive pads to impart a scratch pattern to the surface | Abraslve blast cleaning to achleve a surface profille using non-metallic abrasive media which is suitable to achieve a sharp and angular surface profile. | |||||||||||||||||||||
| Galvanised steel | The surface shall be clean, dry and appear with a rough and dull proflle | Sweep blast-cleaning using non- metallic abraslve leaving a clean, ough and even pattern | |||||||||||||||||||||
| Concrete | Dry abrasive blast cleaning to SSPC- SP 13/NACE No. 6 | Dry abrasive blast cleaning to SSPC- SP 13/NACE No. 6. | |||||||||||||||||||||
| Application | |||||||||||||||||||||||
| Application | methods | ||||||||||||||||||||||
| The product | can be applled by | ||||||||||||||||||||||
| Spray: | Use airless spray | ||||||||||||||||||||||
| Brush: | Recommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness. | ||||||||||||||||||||||
| Roller: | Roller application only to be used for scallops, ratholes, small plpes etc. | ||||||||||||||||||||||
| Date of issue: 25 May 2022 | Page: 2/5 | ||||||||||||||||||||||
| This Technical Data Sheet supersedes those previously issued, | |||||||||||||||||||||||
| The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Gulde (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com | |||||||||||||||||||||||
| Technical | Data | Sheet | |||||||||||||||||||||
| Tankguard | Plus | Jotun Protects Preperty | |||||||||||||||||||||
| Product | mixing ratio(by | volume) | |||||||||||||||||||||
| Tankguard | Plus Comp A | 4 | part(s) | ||||||||||||||||||||
| Tankguard | Plus Comp. B | 1 | part(s) | ||||||||||||||||||||
| Thinner/Cleaning solvent | |||||||||||||||||||||||
| Thinner: Jotun Thinner No. 23 | |||||||||||||||||||||||
| Gulding data for alrless spray Nozzle tip(inch/1000): 17-21 Pressure at nozzle (minimum): 150 bar/2100 psl | |||||||||||||||||||||||
| Drying and Curing time | |||||||||||||||||||||||
| Substrate temperature | 5°C | 10 ℃ | 15 C | 23 C | 30 C | 40C | |||||||||||||||||
| Surface(touch) dry | 24 h | 16 h | 6 h | 4 h | 3 h | 2 h | |||||||||||||||||
| Walk-on-dry | 36 h | 24 h | 10 h | 7 h | 5 h | 3 h | |||||||||||||||||
| For maximum overcoating intervals, refer to the Application Guide (AG) for this product. | |||||||||||||||||||||||
| If a hot cure Is performed Tankguard Plus can be returned to servlce in half the "Drled/cured for servlce" time, as stated below: | |||||||||||||||||||||||
| 5°C:7 d Included 8 h @60°℃ 10 ° ℃: 5d included 8 h @60 ° ℃ 15°℃: 3.5 d induded 8 h @60℃ 23 ° ℃: 2.5 d included 8 h @60°℃ 30°℃: 2 d included 8 h @60℃ 40 °C: 1.5 d induded 8h @60 ℃ | |||||||||||||||||||||||
| Hot cure(by air) can be initiated after the last coat has become "Dry to overcoat", and can be achieved by heating with hot air until a steel temperature of 60 °C is held for 8 hours. Total curing time must be as outlined above. | |||||||||||||||||||||||
| Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the product. | |||||||||||||||||||||||
| Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal tackiness. | |||||||||||||||||||||||
| Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks, Imprints or other physical damage. | |||||||||||||||||||||||
| Dry to over coat, minimum: The recommended shortest time before the next coat can be applied. Drled/cured for servlce: Minimum time before the coating can be permanently exposed to the Intended | |||||||||||||||||||||||
| environment/medium. | |||||||||||||||||||||||
| Date of issue: 25 May 2022 | Page:3/5 | ||||||||||||||||||||||
| This Technical Data Sheet supersedes those previously issued, | |||||||||||||||||||||||
| The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Gulde (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com | |||||||||||||||||||||||
| Technical | Data | Sheet | JOTUN | ||||||||||||||||||||
| Tankguard | Plus | Jotun Protects Preperty | |||||||||||||||||||||
| Induction time and Pot life | |||||||||||||||||||||||
| Paint temperature 23 ℃ Induction time 15 min | |||||||||||||||||||||||
| Pot life 2 h Heat resistance | |||||||||||||||||||||||
| Temperature Continuous | Peak | ||||||||||||||||||||||
| Dry, atmospheric | 160 C | ||||||||||||||||||||||
| [mmersed, sea water | 90 C | 95 ℃ | |||||||||||||||||||||
| [mmersed, crude ai | 160 C | ||||||||||||||||||||||
| Further reslstance Information can be found in Protective Product Resistance List avallable on Jotun's website, or contact your local Jotun office. | |||||||||||||||||||||||
| Peak temperature duration max.1 hour. | |||||||||||||||||||||||
| The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures. | |||||||||||||||||||||||
| Note that the coating will be resistant to various immersion temperatures depending on the specific chemical and whether immersion Iis constant or intermittent. Heat resistance is Infuenced by the total coating system. If used as part of a system, ensure all coatings In the system have similar heat resistance. | |||||||||||||||||||||||
| Product compatibility | |||||||||||||||||||||||
| Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact Jotun for specific system recommendation. | |||||||||||||||||||||||
| Prevlous coat: itself only Subsequent coat: itself only | |||||||||||||||||||||||
| Packaging (typical) | |||||||||||||||||||||||
| Volume | Size of containers | ||||||||||||||||||||||
| (litres) | (litres) | ||||||||||||||||||||||
| Tankguard Plus Comp A | 16 | 20 | |||||||||||||||||||||
| Tankguard Plus Comp. B | 4 | 5 | |||||||||||||||||||||
| The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. | |||||||||||||||||||||||
| Storage | |||||||||||||||||||||||
| Date of issue: 25 May 2022 | Page:4/5 | ||||||||||||||||||||||
| This Technical Data Sheet supersedes those previously issued, | |||||||||||||||||||||||
| The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Gulde (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com | |||||||||||||||||||||||
| Technical | Data Sheet | ||||||||||||||||||||||
| Tankguard | Plus | ||||||||||||||||||||||
| Jotun Protects Preperty | |||||||||||||||||||||||
| The product must be stored in accordance wlth natlonal regulations. Keep the containers in a dry, cool, well ventllated space and away from sources of heat and lgnltlon. Containers must be kept tightly closed. Handle with care. | |||||||||||||||||||||||
| Shelf life at 23 ℃ | |||||||||||||||||||||||
| Tankguard Plus Comp A 24 month(s) Tankguard Plus Comp. B 24 month(s) | |||||||||||||||||||||||
| In some markets commerclal shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quallty is subject to re-Inspection. | |||||||||||||||||||||||
| Caution | |||||||||||||||||||||||
| This product is for professional use only. The applicators and operators shall be trained, expenienced and have the capabilty and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product. This guideline is given based on the current knowledge of the product. Any suggested deviation to sulit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the work. | |||||||||||||||||||||||
| Health and safety | |||||||||||||||||||||||
| Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately. | |||||||||||||||||||||||
| Colour variation | |||||||||||||||||||||||
| When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations from batch to batch. Such products and epoxy based products used as a finish coat may chalk when exposed to sunlight and weathering. | |||||||||||||||||||||||
| Colour and gloss retention on topcoats/finish coats may vary depending on type of colour, exposure environment such as temperature, UV intensity etc., application quality and generic type of paint. Contact your local Jotun office for further information. | |||||||||||||||||||||||
| Disclaime r | |||||||||||||||||||||||
| The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and practical experience. Jotun's products are considered as semi-finished goods and as such, products are often used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves the right to change the given data without further notice. | |||||||||||||||||||||||
| Users should always consult Jotun for specific guidance on the general suitability of this product for their needs and speclfic appllcatlon practices. | |||||||||||||||||||||||
| If there is any inconsistency between different language issues of this document, the English (United Kingdom) verslon will prevall. | |||||||||||||||||||||||
標(biāo)簽： 佐敦